Home and kitchen is a category that lives or dies on thin per-unit margins and high unit counts, so even a few points of added duty on a $35 cookware set or a set of silicone utensils can quietly turn a profitable SKU into a loser. On top of the normal base (MFN) duty, many of these goods can carry additional country- or origin-specific charges depending on where they are made and the rules in effect at import; whether those extra charges apply, and how they combine, depends on the exact HS code and the current tariff schedule. Because the assortment mixes steel, aluminum, plastic, and small electrics under different HS chapters, the same shipment can be dutied at several different rates at once, which is why the impact is easy to miss until a quarter closes light.
Representative 2026 estimate stacking base MFN duty (USITC HTS 2026 Rev.10), Section 301 on China-origin goods (USTR), Section 232 on autos and steel/aluminum/copper articles (CRS IN12545), and the 10% Section 122 surcharge that expires 2026-07-24 and is under appeal (Skadden). Your exact per-SKU duty depends on the precise HS code, which MarginGuard resolves from the live HTS schedule once connected. Not legal or customs advice.
Cambodia is a long-standing low-cost manufacturing base whose exports to the US now carry a reciprocal-era tariff load on top of the normal HTS base duty set by each product's classification. That stacking matters for landed cost: the country-specific load can apply on top of the base rate across many categories, so the duty you pay may no longer be just the historic base rate for your goods, though the exact treatment still depends on your product's HS code. Cambodia has no comprehensive US free trade agreement, so there is no across-the-board duty preference to fall back on, and the representative stacked rate in the box above reflects the current-era treatment. Because rates in this era are set largely through policy action and have been adjusted on short timelines, the number can change between order cycles, so treat it as a snapshot rather than a fixed input.
Cambodia is a genuine China alternative for apparel and footwear and a common first stop when diversifying out of China, but it is not a duty-free escape hatch. It carries its own reciprocal-era load, so the right comparison is Cambodia's stacked rate against China's stacked rate for your specific HS codes, not Cambodia against a pre-tariff baseline. The catch is twofold: the country load is set at the national level, while the duty you actually pay still tracks each product's HS classification, and rules of origin decide whether goods count as Cambodian in the first place. If fabric, components, or major assembly trace back to China, transshipment and substantial-transformation scrutiny can negate the benefit, and any preferential program you hope to use depends on meeting its origin rules. Treat Cambodia as a way to reduce, not eliminate, tariff exposure, and validate the landed-cost delta per SKU before committing volume.
That's a single SKU. Across a full catalog the tariff hits every imported product differently depending on its cost and price — which is exactly why margin damage hides until a quarter closes light.
Paste your Shopify URL. In about ten seconds you'll see every SKU that dropped below your target margin after the current Cambodia tariffs — and the exact price to charge to recover each one. Free, no login.
Scan your store free →Landed cost = unit cost × (1 + tariff rate). To get back to a target margin M, the recovery price is landed cost ÷ (1 − M). For a $35 cookware set from Cambodia at a 16% stacked rate, that means charging $32.48 to hold a 40% margin. Round to a clean price point and test it; the point is to stop selling underwater.
The duty on home and kitchen goods is driven first by what the item is made of, not what it does. Cookware and steel kitchen articles generally fall under HTS chapter 73 (articles of iron or steel), hand tools and cutlery generally sit in chapter 82, and a large plastic and silicone share of the category (storage containers, utensils, gadgets, organizers) generally sits in chapter 39. The base MFN rate for the category tends to run around 6 percent on average, but the exact figure for any given item depends on the specific HS code, which can shift with material, whether the piece is coated or stainless, whether it is a set versus a single article, and whether any part is electric. Sets are a particular trap because, under the set-classification rules, a multi-piece set is generally classified by the single component that gives it its essential character rather than by the item you think you are selling.
Check the controlling material and any electric component per SKU, since a set is generally classified by the component that gives it its essential character (often the higher-duty piece), and an electric component can move an item into a different, often appliance, classification. The exact treatment depends on the specific HS code.
Re-sourcing generally favors light plastic and stainless goods over dense steel and glass, since freight on dense goods can offset a cheaper unit price. The base chapter duty generally follows the product itself, and origin generally shifts only where substantial transformation occurs in the new country, not cosmetic repackaging; the determination depends on the specifics of each case.
Which HS chapters cover home and kitchen goods, and why does it matter?
Most of the category tends to sit across HTS chapters 73 (iron and steel articles like cookware and pans), 82 (cutlery and hand tools), and 39 (plastics, covering storage, utensils, and organizers). The chapter generally turns on the controlling material, not the marketing name, so a single catalog can span all three at different rates. Knowing which chapter each SKU likely falls under helps you estimate the duty instead of guessing, though the exact rate depends on the specific HS code.
Why is my multi-piece kitchen set taxed higher than I expected?
Under the set-classification rules, a retail set is generally classified by the single component that gives it its essential character rather than averaged across the pieces, and that component is often the higher-duty one. A tool set with steel blades and plastic handles can be classified on the steel even though most of the bill of materials is the cheaper plastic. Check the controlling HS code for the set, because the blended rate you assumed may not be how it is treated.
Will moving production out of China fix the tariff hit on cookware?
It may lower country-specific charges, but the base chapter duty generally stays with the product wherever it is made, so you would not escape duty entirely. Light plastic and stainless items tend to move more easily than heavy steel, glass, and ceramics, where freight on dense goods can offset a cheaper unit price. Run the full landed cost for the new origin before switching, and confirm the production move is a genuine substantial transformation rather than repackaging; the exact duty treatment depends on the specific HS code and current rules.
Is sourcing from Cambodia cheaper than from China after tariffs?
Often, but not automatically. Cambodia carries its own reciprocal-era load on top of the base HTS duty, so the saving comes from the gap between Cambodia's stacked rate and China's stacked rate for your exact products, not from any duty-free status. Run the landed-cost math per HS code, since the answer can flip for some categories. This is general guidance, not customs advice.
Does Cambodia qualify for duty-free treatment into the US?
Do not assume so. Cambodia has no comprehensive US free trade agreement, and any preferential program is conditional on meeting its rules of origin, which depend on where materials and processing actually originate. Consider confirming eligibility for your specific goods with a customs broker before pricing a duty-free landed cost. This is general guidance, not customs advice.
Could goods I source from Cambodia be treated as Chinese for tariff purposes?
Possibly, if origin is not genuinely Cambodian. Customs generally looks at substantial transformation, and apparel and footwear typically have category-specific origin rules. If fabric or key components come from China and only light finishing happens in Cambodia, the goods may be treated as Chinese or flagged for transshipment, which can wipe out the intended saving. Keep supplier documentation that supports the country of origin you declare, and confirm the specifics with a customs broker. This is general guidance, not customs advice.
MarginGuard watches every imported SKU and alerts you the moment a tariff change pushes one below your target margin — with the exact recovery price.
Scan your store free →